Just How to Install a Bath Tub Yourself
Just How to Install a Bath Tub Yourself
Blog Article
We've discovered this great article pertaining to Installing A Bathtub below on the net and concluded it made good sense to discuss it with you here.
Mounting a bath tub isn't precisely rocket science, but it does call for solid plumbing, carpentry, and sometimes, tiling abilities. Changing an old bathtub with a new one is additionally a reasonably tough job. If the old tub is conveniently easily accessible, the project can move easily; if you have to open up a wall to get rid of the old tub and place the new bathtub, the job is much harder. In either case, the task is within a house handyman's skills, although you will certainly require a helper to vacate the old bathtub and embeded in the brand-new one. Ensure you have certified yourself for the work as well as are comfortable trying it. Instead of employing a service provider to take over a halfway-completed project, it is far better to think about using one before you start. Possibilities are you may require an expert plumber to make tube links.
This post will aid you install a brand-new tub in your washroom if you have already gotten a brand-new tub and also don't require to alter the arrangement of your previous water system pipes.
Your devices and product checklist must consist of the following:
Getting ready for the Installation
First of all, the sustaining framework provided with the bath must be fitted (if required) according to the maker's instructions. Next, fit the faucets or mixer to the bathtub. When fitting the faucet block, it is important to ensure that if the faucet features a plastic washer, it is fitted between the bathroom and the faucets. On a plastic bathroom, it is likewise reasonable to fit a supporting plate under the faucets system to stop strain on the bath tub.
Fit the flexible faucet adapters to the bottom of the two taps utilizing 2 nuts and also olives (sometimes supplied with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet hole, and after that pass the electrical outlet via the hole in the bath. Make use of the nut supplied by the producer to fit the plug-hole. Check out the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next, fit the end of the versatile overflow pipeline to the overflow electrical outlet. After that, screw the pipe to the overflow face which ought to be fitted inside the bath. Ensure you utilize every one of the provided washing machines.
Connect the trap to the bottom of the waste outlet on the tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the trap to the outlet. Link all-time low of the overflow tube in a comparable manner.The bathroom should now be ready to be fitted in its final setting.
Removing Old Touches
If you require to change old faucets with new ones as a part of your installation, then the first thing you ought to do is disconnect the water supply. After doing so, turn on the taps to drain any type of water staying in the system. The procedure of getting rid of the existing faucets can be fairly bothersome as a result of the limited access that is often the instance.
Utilize a basin wrench (crowsfoot spanner) or a tap device to undo the nut that connects the supply pipelines to the faucets. Have a fabric ready for the continuing to be water that will certainly come from the pipes. As soon as the supply pipes have been gotten rid of, utilize the same device to loosen up the nut that holds the taps onto the bath/basin. You will certainly require to quit the single taps from turning throughout this procedure. When the taps have actually been gotten rid of, the holes in the bath/basin will have to be cleaned of any kind of old securing compound.
Before proceeding to fit the brand-new faucets, compare the pipe links on the old taps to the new faucets. If the old faucets are longer than the new faucets, after that a shank adapter is required for the new faucets to fit.
Setting up the Bathtub
Making use of both wooden boards under its feet, position the tub in the required setting. The wooden boards are handy in evenly spreading the weight of the bath tub over the area of the boards instead of concentrating all the weight onto four tiny factors.
The next objective is to make sure that the bathtub is leveled all round. This can be attained by inspecting the level as well as adjusting the feet on the bath tub up until the spirit level checks out level.
To mount taps, fit all-time low of the furthest adaptable faucet connector to the proper supply pipe by making a compression sign up with; then do the very same for the other faucet.
Switch on the water as well as examine all joints as well as brand-new pipework for leaks and also tighten them if needed. Fill the tub and likewise check the overflow outlet and also the typical electrical outlet for leaks.
Ultimately, repair the bathroom paneling as described in the maker's instruction manual. Tiling as well as securing around the bathtub must wait till the tub has actually been used at the very least once as this will resolve it into its last placement.
Fitting New Touches
If the tails of the new taps are plastic, after that you will need a plastic port to stop damage to the string. One end of the connector fits on the plastic tail of the tap and also the other end offers a link to the existent supply pipes.
If you require to fit a monobloc, after that you will need lowering couplers, which connects the 10mm pipe of the monobloc to the common 15mm supply pipe.
Next, place the faucet in the mounting hole in the bath/basin making certain that the washers are in location in between the tap and the sink. Protect the faucet in position with the producer supplied backnut. As soon as the faucet is securely in place, the supply pipelines can be attached to the tails of the faucets. The taps can either be linked by utilizing corrugated copper piping or with regular faucet connectors. The former type must be attached to the faucet ends first, tightening just by hand. The supply pipelines can later on be attached to the other end. Tighten both ends with a spanner after both ends have been linked.
Tiling Around the Bathtub
In the area where the bath satisfies the ceramic tile, it is needed to secure the accompanies a silicone rubber caulking. This is important as the fitting can move enough to break a stiff seal, triggering the water to pass through the wall surface in between the bathroom and also the tiling, bring about complications with dampness and possible leaks to the ceiling below.
You can choose from a variety of coloured sealants to blend in your fixtures and fittings. They are sold in tubes and cartridges, and are capable of sealing gaps up to a width of 3mm (1/8 inch). If you have a bigger void to load, you can load it with spins of drenched paper or soft rope. Keep in mind to constantly load the bath tub with water before sealing, to allow for the movement experienced when the tub is in use. The sealant can break fairly early if you do not consider this movement before sealing.
Conversely, ceramic coving or quadrant tiles can be used to border the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as cut to size, are also easily readily available on the marketplace. It is a good idea to fit the ceramic tiles using waterproof or water resistant sticky as well as grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I hope you enjoyed our article about A Step-by-Step Guide to Installing a Bathtub. Thank you for taking the time to browse our article. Liked our review? Please share it. Let someone else find it. Thank you for your time. Don't forget to come visit our site back soon.
Show Details
Report this page